Book Appointment Now
Advanced ZYF300CA-P Radar High-Frequency PCB Manufacturing
ZYF300CA-P radar high-frequency PCB is a 2-layer circuit board fabricated on ZYF300CA-P, a premium PTFE-based high-frequency laminate from Changzhou Zhongying Technology. Engineered with 1.6mm board thickness, 2 oz outer copper, 0.2mm minimum through-holes and ENIG 2 µ” surface finish, it delivers outstanding electrical performance, mechanical strength and routing capability — widely adopted in radar systems, wireless communication, RF test equipment and microwave backhaul hardware as a reliable, cost-efficient drop-in alternative to Rogers RO3003. It is manufactured at our group’s Shenzhen campus alongside high-speed and high-frequency PCB and advanced HDI PCB production lines.
✓ PTFE-Based Low-Loss Laminate
Stable Dk, ultra-low Df
✓ Rogers RO3003 Drop-In Alternative
Comparable performance, domestic supply
✓ 2 oz Heavy Copper Outer Layers
High-current RF, better thermal
✓ 0.2mm Precision Through-Holes
Tight-tolerance plated vias
✓ ENIG 2 µ” Surface Finish
Flat pads, excellent solderability
✓ One-Stop PCB + PCBA
Fabrication to assembly under one roof

2
Layer Count
1.6mm
Board Thickness
ZYF300CA-P
Base Material
2 oz
Outer Copper
0.2mm
Min Through Hole
ISO 9001:2015
ISO 14001
UL (E305905)
IPC Class 2 / Class 3
IATF 16949
RoHS
Table of Contents
ZYF300CA-P 2-Layer Radar High-Frequency PCB Stackup
A clean, symmetric 2-layer construction optimized for RF signal integrity, controlled impedance and high-power handling.
- L1 (Top) – Signal / RF Layer: 2 oz copper, ENIG 2 µ” finish, 15/15mil minimum trace width/spacing, RF pads and antenna feed networks. This is the layer that carries most of the insertion-loss budget on a ZYF300CA-P radar high-frequency PCB, so surface finish and copper roughness matter as much as trace geometry.
- Dielectric Core – ZYF300CA-P Laminate: 1.6mm PTFE-based high-frequency substrate with stable Dk and low Df, a halogen-free option, and low moisture absorption that keeps electrical performance repeatable after assembly. Because the laminate is produced in volume domestically, a ZYF300CA-P radar high-frequency PCB build does not depend on imported material lead times or lot matching.
- L2 (Bottom) – Signal / Ground Layer: 2 oz copper, ENIG 2 µ” finish, continuous ground plane for shielding and return-path integrity.
Custom Stackup Optimization: Need controlled impedance (50/75Ω), a mixed-dielectric build, or a different thickness? Send us your Gerber files and our engineering team will recommend the optimal ZYF300CA-P stackup for your design.
Technical Specifications & Manufacturing Capabilities
Standard mass-production parameters for the ZYF300CA-P radar high-frequency PCB, with Season PCB’s extended advanced capabilities for samples and special requirements.
| Parameter | Specification | Advanced Capabilities |
| Layer Count | 2-Layer | 2-30L (Mass); 2-64L (Sample) |
| Base Material | ZYF300CA-P (Zhongying Tech) | Rogers, Taconic, Arlon, PTFE, F4B, Isola, Megtron |
| Board Thickness | 1.6mm ±10% | 0.2-6.4mm (Mass); 0.15-6.4mm (Sample) |
| Panel Size | 160 × 132 mm (1-up panel) | 480 × 600mm (Mass); 1050 × 610mm (Sample) |
| Copper Thickness | Outer: 2 oz | Outer: 1/3–12 oz; Inner: 1/4–12 oz |
| Min Drill Size | 0.20mm | 0.15mm (Mass); 0.127mm (Sample) |
| Min Trace Width/Spacing | 15/15mil | 2/2mil (Sample); 2.36/2.36mil (Mass, 1 oz) |
| Min BGA Pad | N/A | 0.15mm |
| Surface Finish | ENIG (Immersion Gold) 2 µ” | OSP, HASL, ENIG, ENEPIG, Immersion Silver & Tin, Electric Hard Gold |
| Impedance Control | ±10% | ±5% (Strict Tolerance) |
| Specialized Processes | Controlled-depth routing | Back Drilling, Edge Plating, Cavity Boards, Conductive Via Fill |
| Solder Mask | Customer-specified color | LPI (liquid photo-imageable), matte or gloss |
| Min Routing Tolerance | ±0.15mm | ±0.075mm |
| Quality Standard | IPC Class 2, RoHS | IPC Class 3, UL, IATF 16949 |
| PCB Type | High-Frequency PCB (2L) | HDI, Multilayer, Rigid-Flex, High Speed, Hybrids & Mixed Dielectrics |
ZYF300CA-P Radar High-Frequency PCB — Built for RF Performance, Mechanical Strength & Scalable Production
ZYF300CA-P is a high-frequency laminate engineered for demanding RF and microwave applications. When fabricated by Season PCB into a 2-layer radar high-frequency PCB, it delivers a rare combination of electrical excellence, mechanical rigidity and routing flexibility — three properties that are usually in tension on alternative substrates.
The board’s low-loss dielectric core keeps signal attenuation to a minimum across the microwave spectrum, while the 2 oz outer copper supports elevated RF power levels without excessive heating. The result is a radar PCB that sustains high-speed, high-capacity data transmission with stable, accurate signal integrity — exactly what radar transceivers, antenna feed networks, microwave backhaul links and 5G base-station front-ends demand.
Because ZYF300CA-P is produced in volume by Changzhou Zhongying Technology with tight lot-to-lot consistency, it offers a repeatable, supply-secure alternative to imported Rogers RO3003. Season PCB keeps the laminate in standing inventory, so prototypes and production runs follow a predictable schedule. For a ZYF300CA-P radar high-frequency PCB program, that consistency matters more than any single benchmark number: Dk tolerance, copper roughness and dielectric thickness stay inside the same window from the first prototype panel to the tenth production lot.
What Makes This ZYF300CA-P Radar High-Frequency PCB Exceptional
Stable Dielectric Constant (Dk)
Consistent, tightly controlled Dk across frequency and temperature keeps phase and impedance predictable — critical for radar ranging accuracy.
Ultra-Low Dissipation Factor (Df)
Minimal dielectric loss preserves signal amplitude over long RF traces, improving receiver sensitivity and reducing heat generation.
Direct RO3003 Replacement
Similar electrical profile to Rogers RO3003 with predictable domestic supply, plus the mechanical robustness needed for board-level assembly.
2 oz Heavy Copper Construction
70 µm copper layers carry higher RF currents, spread heat evenly and keep conductor losses low on power-intensive modules.
Outstanding Mechanical Strength
The laminate’s rigid core resists warpage and vibration — essential for automotive radar, industrial sensing and field-deployed equipment.
Precision 15/15mil Routing
Fine, repeatable trace geometry supports tight impedance control and clean routing of differential pairs and RF channels.
ENIG 2 µ” Finish for Reliability
Immersion gold protects pads from oxidation, enables wire bonding options and ensures flat surfaces for fine-pitch SMT.
Turnkey PCB + PCBA Service
From bare board to fully assembled, tested RF module — one partner, one BOM, zero hand-offs.
Where the ZYF300CA-P Radar High-Frequency PCB Delivers Maximum Impact
Radar Systems
Automotive mmWave radar, marine radar, security surveillance and meteorological radar front-ends that demand low-loss, phase-stable boards.
Wireless Communication
5G base-station antennas, fiber-optic modules and microwave backhaul equipment requiring consistent high-frequency performance.
Microwave Backhaul & Point-to-Point Radio
Point-to-point microwave links, backhaul radios and upconverter modules where material stability under temperature swings is non-negotiable.
Industrial & Security Sensing
Security scanners, industrial inspection heads and motion-sensing front-ends that demand heat resistance, dimensional stability and mechanical integrity across long duty cycles.
Automotive Radar & ADAS
77/79GHz radar modules, ADAS sensor clusters and in-cabin monitoring units that need stable Dk and low insertion loss across the automotive temperature range.
RF Test & Instrumentation
Test fixtures, couplers and measurement front-ends that need repeatable, calibration-stable PCB performance.
Design Guidelines for a ZYF300CA-P Radar High-Frequency PCB
Trace Width & Impedance Targets
When you lay out a ZYF300CA-P radar high-frequency PCB, start from the 15/15mil process floor and let your field solver set the final trace width against the laminate’s Dk. Keep the same stackup across prototype and production, and place impedance coupons on the panel rail so measured values — not nominal ones — drive the release.
Ground Via Stitching & RF Return Path
On any ZYF300CA-P radar high-frequency PCB, return current follows the path of least impedance. Stitch ground vias along RF traces at a fraction of a wavelength, keep antenna feed lines clear of plane splits, and route digital return currents on a plane separate from the microwave section.
Panelization for Soft PTFE Laminates
PTFE is softer than FR-4, so panel design matters. Give a ZYF300CA-P radar high-frequency PCB generous rails, prefer routing over aggressive V-score near plated holes, and keep breakaway tabs short to limit stress at the dielectric edge during depaneling.
Assembly & Moisture Control
Bake a ZYF300CA-P radar high-frequency PCB before reflow to drive out absorbed moisture, then run a profile with moderate ramp rates so the dielectric does not expand faster than the copper. ENIG pads on this laminate wet reliably with standard no-clean and water-soluble pastes. Store panels in moisture-barrier bags with desiccant once the bake is complete — a second bake cycle costs far less than delamination found after assembly.
Pushing Precision to the Limit — How We Build It
Challenge #1: Etching Accuracy on 2 oz Copper + PTFE Laminate
The Problem: PTFE-based laminates are soft and dimensionally sensitive, and 2 oz copper is harder to etch cleanly. Together they create a real risk of undercut, ragged edges and impedance drift on RF traces.
Our Solution:
- Dedicated high-frequency material handling line with controlled bake-out and tension settings.
- Advanced etching chemistry tuned for thick copper, followed by AOI verification of edge quality.
- Impedance test coupons on every panel to confirm 50/75Ω targets before release.
Challenge #2: 0.2mm Plated Through-Holes in PTFE Material
The Problem: Drilling PTFE-based laminates produces smear and rough hole walls, which can cause plating voids and intermittent RF connections.
Our Solution:
- CNC drilling with sharpened carbide bits and optimized feeds for clean hole walls in soft substrates.
- Plasma or chemical desmear step to remove resin smear before electroless copper.
- 100% electrical test plus microsection sampling to verify annular ring and plating thickness.
Rigorous Testing — Every Board, Every Batch
Automated Optical Inspection (AOI)
Scans every trace, pad and via for opens, shorts and etching defects on both layers.
Flying Probe / E-Test
100% electrical testing verifies continuity and isolation across the full netlist.
TDR Impedance Testing
Time-domain reflectometry validates controlled impedance on RF and high-speed nets.
Microsection Analysis
Cross-sections verify copper thickness, plating integrity and drill quality on every lot.
Thermal Stress Testing
Simulated reflow and thermal cycling confirm solderability and laminate stability.
Dimensional & Appearance Check
Final profile measurement and cosmetic inspection ensure the board meets IPC Class 2/3 criteria.
Six Reasons Global RF & Radar Brands Choose Season PCB
PCB Manufacturing Since 2006
Established in 2006 under the 998PCB Group, Season PCB has supported RF and radar programs across Europe, North America and Asia.
Standing High-Frequency Material Inventory
ZYF300CA-P, Rogers, Taconic, Arlon, PTFE, F4B and Isola kept in stock — standing inventory keeps the build schedule predictable.
Prototype Support for Qualified Projects
Eligible projects receive high-frequency PCB samples for design validation — see our sample program for details.
IPC Class 2 / Class 3 Compliance
Processes aligned with IPC-6012, IPC-A-600 and IPC-6018 for consistent, certifiable quality.
One-Stop PCB + PCBA Service
Fabrication, component sourcing, SMT and full functional testing under one roof reduces your supply-chain risk.
Global Delivery & Engineering Support
Fast worldwide shipping and engineering support from DFM review to mass-production ramp-up.
Compatible High-Frequency Materials & Direct Replacements
Rogers RO3003
Direct drop-in replacement with comparable Dk/Df performance on domestically produced laminate — ideal for radar and 77GHz automotive sensing.
Rogers RO4000 Series
For designs already on RO4003C/RO4350B, we can run side-by-side RF validation on ZYF300CA-P or keep your existing material.
Taconic TLY / Arlon
Experienced fabricating on Taconic and Arlon PTFE laminates for high-frequency and RF programs.
F4B / PTFE & Isola
Domestic F4B and PTFE substrates plus Isola high-speed options for cost-sensitive microwave designs.
From Gerber to Shipped Panel — How a ZYF300CA-P Radar High-Frequency PCB Order Runs
Engineering DFM Review
Every ZYF300CA-P radar high-frequency PCB order starts with a DFM review: trace width against laminate Dk, annular ring on 0.2mm holes, impedance coupon placement and panel utilization. Findings come back in writing before fabrication is released.
Fabrication & In-Process Test
Panels run on a dedicated high-frequency line with controlled bake-out, plasma treatment before plating and AOI after etching. Each ZYF300CA-P radar high-frequency PCB panel carries impedance coupons and passes flying-probe test before it leaves the line.
Documentation & Delivery
Shipments include material certificates, microsection images on request and impedance measurements for every coupon. A single ZYF300CA-P radar high-frequency PCB prototype and a full production release travel with the same documentation package, so incoming inspection never has to guess.
As a professional high-frequency PCB manufacturer, Season PCB specializes in ZYF300CA-P radar high-frequency PCBs, Rogers-based microwave boards, PTFE antennas and mixed-dielectric RF stacks. Our high-frequency PCB factory supports 2-30 layer production with laser drilling, controlled impedance and ENIG finishing, serving radar, 5G, RF test and microwave backhaul customers across Europe, North America and Asia.
Whether you need a quick-turn ZYF300CA-P PCB prototype, a cost-efficient RO3003 alternative for mass production, or a full turnkey RF PCB assembly, our engineering team is ready. Send your Gerber files today for a DFM review and a competitive quotation from our engineering team — and ask about our high-frequency PCB sample program for qualified projects.
For PTFE-free double-sided RF work on Rogers hydrocarbon ceramic, see our double-sided RO4350B PCB page.
Explore Related Resources: Discover our complete high-frequency PCB solutions for radar and RF applications, browse high-speed PCB manufacturing for advanced digital designs, or view all PCB products including our 12-layer 1-stage HDI PCB and HDI PCB capabilities. For material alternatives, see our multilayer PCB and fast PCB prototyping services. For more group capabilities, visit our sister site 998pcb.com for 2-30 layer multilayer PCB, HDI PCB and one-stop PCBA assembly.
Frequently Asked Questions
Common inquiries about ZYF300CA-P radar high-frequency PCB manufacturing
What is a ZYF300CA-P radar high-frequency PCB?
A ZYF300CA-P radar high-frequency PCB is a 2-layer circuit board manufactured on ZYF300CA-P, a PTFE-based high-frequency laminate produced by Changzhou Zhongying Technology. It combines excellent electrical performance, mechanical strength and routing capability, making it ideal for radar systems, wireless communication, RF test equipment and microwave backhaul hardware. It is widely used as a cost-efficient drop-in replacement for Rogers RO3003. Designers usually shortlist a ZYF300CA-P radar high-frequency PCB build when imported laminate lead times or lot matching become the bottleneck.
Is ZYF300CA-P a suitable alternative to Rogers RO3003?
Yes. ZYF300CA-P is engineered as a drop-in alternative to Rogers RO3003, offering comparable dielectric constant, low dissipation factor and stable high-frequency performance on domestically produced laminate. Season PCB can run side-by-side impedance and insertion-loss verification on a ZYF300CA-P radar high-frequency PCB against your existing RO3003 stackup, so the substitution is qualified on measured data rather than datasheet values.
Why use 2 oz outer copper on a high-frequency PCB?
2 oz (70 µm) outer copper increases current-carrying capacity, improves thermal dissipation for high-power RF amplifiers, and reduces conductor insertion loss for radar and communication modules that handle elevated power levels. It is a common choice for antenna feed networks, power combiners and radar transceiver boards. On a ZYF300CA-P radar high-frequency PCB, the thicker outer layer also means wider minimum spacing, so budget the trace pitch before the panel is finalized.
Can Season PCB supply samples for high-frequency PCB evaluation?
Yes. Season PCB supplies evaluation samples for qualified high-frequency and high-speed projects. Standing inventory of ZYF300CA-P, Rogers, Taconic, Arlon, PTFE, F4B and Isola laminates keeps sample scheduling predictable. Send your stackup and panel requirements to our engineering team to confirm availability.
How is ZYF300CA-P prototype scheduling handled?
Prototype scheduling for 2-layer ZYF300CA-P boards depends on laminate stock, surface finish and the number of impedance test coupons on the panel. Our engineering team reviews your Gerber package and confirms the schedule in writing before release, so your RF validation plan is locked against a known milestone. Mass-production slots are planned from the same confirmed baseline.
Ready to Build Your ZYF300CA-P Radar High-Frequency PCB?
Whether you need a single ZYF300CA-P prototype for RF validation or high-volume production runs, Season PCB delivers precision, speed and certified quality. Upload your Gerber files for a DFM review and a quotation from our engineering team.
Need the two-layer counterpart for shorter, lower-loss feed runs? Our double-sided high-frequency PTFE PCB page covers the Taconic platform behind these radar builds.
